74HC00D
Toshiba Halbleiter und Speicher
- Lifecycle
- Active
- Stock
- 4166 Stückzahl
- Package
- SOIC-14
- Series
- Logic-Gates und Wechselrichter
Dieser detaillierte Vergleich von 74HC00D und 74HC03D-Q100J bietet wertvolle Einblicke in deren Spezifikationen und Hauptmerkmale. Wir gehen ausführlich auf wichtige Faktoren ein, darunter RoHS-Konformität, REACH-Status, Serie, Montageart, Gehäusetyp und weitere relevante Eigenschaften. Die übersichtliche Darstellung der Unterschiede vereinfacht die Komponentenauswahl und erleichtert Ihnen die Wahl der optimalen Lösung für Ihre Anwendung.
Replacement verdict
The 74HC00D and 74HC03D-Q100J are not functionally interchangeable. Although both are quad 2-input NAND gates in the same SO14 package, the 74HC00D provides standard push-pull CMOS outputs, whereas the 74HC03D-Q100J features open-drain outputs that require external pull-up resistors. This fundamental output architecture difference, combined with the automotive-grade qualification of the 74HC03D-Q100J, makes direct substitution impractical without circuit redesign.
Toshiba Halbleiter und Speicher
Nexperia USA Inc.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | 74HC00D | 74HC03D-Q100J | Why it matters |
|---|---|---|---|
| Logic Function | Quad 2-input NAND gate | Quad 2-input NAND gate with open-drain outputs | The 74HC00D has standard push-pull outputs, while the 74HC03D-Q100J has open-drain outputs, which fundamentally changes how the output can be used in a circuit. |
| Output Type | Push-pull (CMOS) | Open-drain | Push-pull outputs can source and sink current actively, whereas open-drain outputs can only sink current and require an external pull-up resistor, affecting drive capability and interfacing. |
| Output Drive Current (IOL/IOH) | ±4 mA (at VCC = 4.5 V) | 4 mA (IOL only; no IOH sourcing) | The 74HC00D can both source and sink current, while the 74HC03D-Q100J can only sink current, limiting its ability to directly drive loads that require a high logic level. |
| Propagation Delay (tPD) | ~9 ns (at VCC = 4.5 V, typical) | ~13 ns (at VCC = 4.5 V, typical) | Different propagation delays affect timing margins in high-speed digital circuits and may impact signal integrity in synchronous designs. |
| Qualification Standard | Standard commercial/industrial grade | AEC-Q100 qualified (automotive grade) | The Q100J suffix indicates automotive qualification, meaning the 74HC03D-Q100J is tested for higher reliability and temperature extremes, making it suitable for automotive applications. |
| Operating Temperature Range | -40°C to +125°C | -40°C to +125°C (AEC-Q100 qualified) | Although the temperature range is similar, the automotive qualification ensures stricter testing and reliability for the 74HC03D-Q100J in harsh environments. |
| Package | SO14 (SOIC-14) | SO14 (SOIC-14) | Both use the same package, so footprint compatibility is maintained, but the electrical differences still prevent direct substitution. |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | Both operate over the same supply voltage range, so power supply compatibility is not a differentiator. |
| Input Type | Standard CMOS input | Standard CMOS input | Input characteristics are identical, so input interfacing is compatible between the two devices. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | 74HC00D | 74HC03D-Q100J |
|---|---|---|
| Supplier | - | Nexperia USA Inc. |
| Series | 74HC | Automotive, AEC-Q100, 74HC |
| Part Status | Active | Active |
| Logic Type | NAND Gate | NAND Gate |
| Number of Circuits | 4 | 4 |
| Number of Inputs | 2 | 2 |
| Features | - | Open Drain |
| Voltage - Supply | 2V ~ 6V | 2V ~ 6V |
| Current - Quiescent (Max) | 1 µA | 2 µA |
| Current - Output High Low | 5.2mA, 5.2mA | -, 5.2mA |
| Logic Level - Low | 0.5V ~ 1.8V | 0.5V ~ 1.8V |
| Logic Level - High | 1.5V ~ 4.2V | 1.5V ~ 4.2V |
| Max Propagation Delay @ V Max CL | 13ns @ 6V, 50pF | 16ns @ 6V, 50pF |
| Operating Temperature | -40°C ~ 125°C | -40°C ~ 125°C |
| Mounting Type | Surface Mount | Surface Mount |
The 74HC00D contains four independent 2-input NAND gates with standard push-pull (totem-pole) outputs. The 74HC03D-Q100J contains four independent 2-input NAND gates with open-drain outputs, meaning each output requires an external pull-up resistor to define the high logic level.
Yes. Both devices are offered in the SO14 package and use the same standard 14-pin pinout for a quad 2-input NAND gate function, with pins 1, 2, 4, 5, 9, 10, 12, and 13 as inputs, pins 3, 6, 8, and 11 as outputs, pin 7 as GND, and pin 14 as VCC. However, the open-drain outputs of the 74HC03D-Q100J require external pull-up resistors, which the 74HC00D does not.
No, not without circuit modification. The 74HC00D has active push-pull outputs, while the 74HC03D-Q100J has open-drain outputs. Replacing an open-drain device with a push-pull device can cause bus contention if multiple outputs are tied together, and it removes the ability to wire-AND outputs or level-shift via an external pull-up. Conversely, replacing a 74HC00D with a 74HC03D-Q100J requires adding pull-up resistors and verifying the resulting rise times and logic levels.
Both the 74HC00D and the 74HC03D-Q100J are HC-family CMOS devices typically specified for a supply voltage range of 2.0 V to 6.0 V, with nominal 5 V operation. They provide standard HC input thresholds and are compatible with LSTTL output levels when operated at 5 V. Exact limits should be confirmed on the respective manufacturer datasheets.
The Q100 suffix indicates that the device is qualified to the AEC-Q100 standard for automotive-grade integrated circuits. This means it has undergone additional stress testing and qualification for use in automotive and other high-reliability applications. The 74HC00D, as a standard commercial part, does not carry this automotive qualification.
The 74HC00D provides standard CMOS push-pull outputs that can both source and sink current, typically in the range of ±4 mA at 5 V. The 74HC03D-Q100J provides open-drain outputs that can only sink current to ground; the high state is achieved only through an external pull-up resistor. The sink current capability of the 74HC03D-Q100J is typically comparable to the 74HC00D, but the source current is determined by the external pull-up and the output low-impedance path is absent in the high state.
The 74HC03D-Q100J is suitable for wired-AND configurations because its open-drain outputs can be tied together with a single pull-up resistor to implement a logical AND of the outputs. The 74HC00D cannot be used in this manner because its push-pull outputs would contend with each other if tied together, potentially causing excessive current and unreliable logic levels.
The input switching thresholds are the same for both devices because they share the same HC-family input structure. The output voltage levels differ: the 74HC00D produces standard CMOS output high and low levels, while the 74HC03D-Q100J produces a low level when on and a high-impedance state when off, with the actual high level determined by the external pull-up resistor and load. Therefore, the output high voltage of the 74HC03D-Q100J is not internally fixed.