ADM4853ARZ
Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 6517 Stückzahl
- Package
- SOIC-8
- Series
- Interface-Treiber, Empfänger, Transceiver
Dieser detaillierte Vergleich von ADM4853ARZ und ADM4856AR bietet wertvolle Einblicke in deren Spezifikationen und Hauptmerkmale. Wir gehen ausführlich auf wichtige Faktoren ein, darunter RoHS-Konformität, REACH-Status, Serie, Montageart, Gehäusetyp und weitere relevante Eigenschaften. Die übersichtliche Darstellung der Unterschiede vereinfacht die Komponentenauswahl und erleichtert Ihnen die Wahl der optimalen Lösung für Ihre Anwendung.
Replacement verdict
The ADM4853ARZ and ADM4856AR are both half-duplex RS-485/RS-422 transceivers in 8-lead SOIC packages with matched supply voltage and data-rate classes, making them a viable functional replacement pairing. However, the ADM4856AR is specified for full-duplex operation while the ADM4853ARZ is a half-duplex device, so the replacement is only valid where the application does not require simultaneous transmit and receive. Pinout and driver/receiver enable logic should be validated against the target board before substitution.
Analog Devices Inc.
Analog Devices Inc.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM4853ARZ | ADM4856AR | Why it matters |
|---|---|---|---|
| Data Rate | 10 Mbps | 20 Mbps | Maximum signaling speed; the faster device supports higher-throughput buses and shorter bit times. |
| Duplex Mode | Half duplex | Full duplex | Determines whether simultaneous transmit and receive is possible; full duplex needs separate A/B and Y/Z pairs. |
| Number of Drivers / Receivers | 1 driver, 1 receiver | 1 driver, 1 receiver | Defines the transceiver channel count and how many bus nodes each package can serve. |
| Receiver Input Impedance (Unit Loads) | 1 unit load (1/32) | 1 unit load (1/32) | Sets how many receivers can share a bus; lower unit load allows more nodes on the same differential pair. |
| Supply Voltage | 5 V | 5 V | Must match the system rail; both are 5 V RS-485 transceivers, so power design is compatible. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Confirms industrial temperature capability for reliable operation in harsh environments. |
| Package / Mounting | 8-SOIC (surface mount) | 8-SOIC (surface mount) | Footprint and assembly compatibility; identical package allows drop-in PCB replacement. |
| Fail-Safe Receiver | Yes (open/short fail-safe) | Yes (open/short fail-safe) | Guarantees a defined logic output when the bus is idle, open, or shorted, preventing false data. |
| ESD Protection (Bus Pins) | ±15 kV HBM | ±15 kV HBM | Indicates robustness against electrostatic discharge on exposed bus lines during handling and field use. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM4853ARZ | ADM4856AR |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC |
| Part Status | Active | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS422, RS485 | RS422, RS485 |
| Number of Drivers/Receivers | 1/1 | 1/1 |
| Voltage - Supply | 4.75V ~ 5.25V | 4.75V ~ 5.25V |
| Mounting Type | Surface Mount | Surface Mount |
| Duplex | Half | - |
| Receiver Hysteresis | 20 mV | - |
| Data Rate | 10Mbps | - |
| Operating Temperature | -40°C ~ 85°C | - |
The ADM4853ARZ is a half-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package with a 10 Mbps maximum data rate, while the ADM4856AR is a full-duplex RS-485/RS-422 transceiver in a 14-lead SOIC package with a 2.5 Mbps maximum data rate. The ADM4853ARZ also includes a driver enable and receiver enable pin configuration for half-duplex bus sharing, whereas the ADM4856AR provides separate driver and receiver paths for full-duplex communication.
No. The ADM4853ARZ is supplied in an 8-lead SOIC package, and the ADM4856AR is supplied in a 14-lead SOIC package. The pin counts and pin functions differ, so they are not drop-in replacements for each other.
The ADM4853ARZ supports a maximum data rate of 10 Mbps. The ADM4856AR supports a maximum data rate of 2.5 Mbps. The data rate must be verified against the specific grade and manufacturer datasheet revision before design release.
The ADM4853ARZ is a half-duplex transceiver, using a shared differential bus pair with driver and receiver enable control. The ADM4856AR is a full-duplex transceiver, providing separate driver outputs and receiver inputs for simultaneous transmit and receive operation.
Both devices are specified for a single 5 V supply. The designer should confirm the exact supply range and tolerance from the official Analog Devices datasheet for the selected grade before finalizing the power design.
They can coexist on the same RS-485 bus only if the network topology and protocol account for the half-duplex ADM4853ARZ and the full-duplex ADM4856AR. Full-duplex devices require four-wire cabling, while half-duplex devices use two-wire cabling, so mixing them requires careful wiring and bus arbitration design.
The ADM4853ARZ is offered in an 8-lead SOIC package, and the ADM4856AR is offered in a 14-lead SOIC package. Both are industrial-grade transceivers, but the exact operating temperature range and package thermal limits must be verified from the manufacturer datasheet for the specific orderable part number.