ADS1231IDR vs ADS1286UCG4

Dieser detaillierte Vergleich von ADS1231IDR und ADS1286UCG4 bietet wertvolle Einblicke in deren Spezifikationen und Hauptmerkmale. Wir gehen ausführlich auf wichtige Faktoren ein, darunter RoHS-Konformität, REACH-Status, Serie, Montageart, Gehäusetyp und weitere relevante Eigenschaften. Die übersichtliche Darstellung der Unterschiede vereinfacht die Komponentenauswahl und erleichtert Ihnen die Wahl der optimalen Lösung für Ihre Anwendung.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Not a drop-in replacement

The ADS1231IDR and ADS1286UCG4 are not drop-in replacements for one another. The ADS1231IDR is a 24-bit low-noise bridge sensor ADC with an integrated PGA and on-chip oscillator, while the ADS1286UCG4 is a 12-bit successive-approximation ADC with a differential input and serial interface. They differ in resolution, architecture, input configuration, and package, so a direct substitution is not feasible without redesign.

Different resolution Different ADC architecture Different input configuration Different package

Parts at a glance

Part A

ADS1231IDR

Texas Instruments

Lifecycle
Active
Stock
4314 Stückzahl
Package
SOIC-16
Series
Datenerfassung mit Analog to Digital Converters (ADC)
Part B

ADS1286UCG4

Texas Instruments

Lifecycle
Active
Stock
2980 Stückzahl
Package
SOIC-8
Series
Datenerfassung mit Analog to Digital Converters (ADC)

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADS1231IDR ADS1286UCG4 Why it matters
Resolution (bits) 24 12 Resolution determines the smallest signal change the ADC can distinguish; a 24-bit device offers far finer measurement granularity than a 12-bit device.
Number of input channels 1 (differential) 1 (differential) Both are single-channel differential devices, so channel count is not a differentiator for substitutability.
Interface type Serial (SPI-compatible, 2-wire) Serial (SPI-compatible) The digital interface must match the host controller; both use serial interfaces but with differing protocol details that affect firmware compatibility.
Supply voltage (analog) 2.7 V to 5.3 V 4.5 V to 5.5 V The analog supply range determines compatibility with the system power rail; the ADS1231 supports lower-voltage rails than the ADS1286.
Input type / architecture Delta-sigma with integrated PGA SAR (successive approximation) Delta-sigma converters excel at low-speed high-resolution measurements, while SAR converters offer faster sampling; architecture affects noise, speed, and application fit.
Data rate / sampling rate 10 SPS or 80 SPS (selectable) Up to 20 kSPS Sampling rate determines how fast the system can capture changing signals; the SAR device is far faster while the delta-sigma device targets slow precision measurements.
Package type SOIC-8 (8-pin) VSSOP-8 / MSOP-8 Package footprint and pinout must match the PCB layout for a drop-in replacement; differing packages require layout changes.
Operating temperature range -40 °C to +85 °C -40 °C to +85 °C Both cover the industrial temperature range, so environmental compatibility is equivalent.
Integrated PGA / gain stage Yes (gain 128) No An integrated PGA allows direct connection of low-level sensors without external amplification, simplifying the signal chain for the ADS1231.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADS1231IDR ADS1286UCG4
Supplier - Texas Instruments
Part Status Active Discontinued at Digi-Key
Number of Bits 24 12
Sampling Rate(Per Second) 80 20k
Number of Inputs 1 1
Input Type Differential Differential
Data Interface SPI SPI
Configuration ADC S/H-ADC
Ratio - S / H: ADC - 1:1
Number of A/D Converters 1 1
Architecture Sigma-Delta SAR
Reference Type External External
Voltage - Supply, Analog 3V ~ 5.3V 5V
Voltage - Supply, Digital 3V ~ 5.3V 5V
Operating Temperature -40°C ~ 85°C -40°C ~ 85°C

Frequently asked questions

What are the primary functional differences between the ADS1231IDR and ADS1286UCG4?

The ADS1231IDR is a 24-bit delta-sigma analog-to-digital converter with an integrated low-noise programmable gain amplifier (PGA) and a bridge excitation voltage, designed primarily for weigh-scale and strain-gauge applications. The ADS1286UCG4 is a 12-bit successive-approximation-register (SAR) ADC with a pseudo-differential input and an SPI-compatible serial interface, intended for general-purpose medium-speed data acquisition. They differ fundamentally in resolution architecture (delta-sigma vs SAR), resolution (24-bit vs 12-bit), and integration level.

Are the ADS1231IDR and ADS1286UCG4 pin-to-pin or package compatible?

No. The ADS1231IDR is supplied in an 8-pin SOIC (D) package, while the ADS1286UCG4 is supplied in a 10-pin VSSOP (DGS) package. The pin counts, pin functions, and package footprints differ, so they are not drop-in replacements and require different PCB land patterns.

What are the supply voltage requirements for each device?

The ADS1231IDR operates from a single analog supply (AVDD) of 2.7 V to 5.3 V and a digital supply (DVDD) of 2.7 V to 5.3 V. The ADS1286UCG4 operates from a single supply of 2.7 V to 5.25 V. Both are low-voltage single-supply devices, but the exact specified ranges differ slightly and should be verified against the respective datasheets.

How do the input configurations and interfaces differ?

The ADS1231IDR provides a fully differential input with an integrated PGA (gain of 128) and a dedicated bridge excitation output, and it uses a simple two-wire serial interface for data readout. The ADS1286UCG4 provides a pseudo-differential input without an integrated PGA and uses a standard SPI-compatible serial interface (CS, SCLK, DOUT). The ADS1231IDR is optimized for direct sensor connection, whereas the ADS1286UCG4 requires external signal conditioning for low-level sensors.

Which device is better suited for precision weigh-scale or strain-gauge applications?

The ADS1231IDR is specifically designed for weigh-scale and strain-gauge applications because it integrates a low-noise PGA, a 24-bit delta-sigma modulator, and a bridge excitation voltage source in a single package. The ADS1286UCG4, being a 12-bit SAR ADC without an integrated PGA or excitation source, would require external amplification and excitation circuitry and would provide lower resolution, making it less suitable for high-precision bridge sensor applications.

What are the data output rates of the ADS1231IDR and ADS1286UCG4?

The ADS1231IDR provides a selectable output data rate of 10 SPS or 80 SPS. The ADS1286UCG4 is a SAR converter whose throughput is determined by the external serial clock; its maximum sampling rate is specified in its datasheet (typically up to 200 kSPS depending on SCLK). The ADS1231IDR is therefore intended for low-speed, high-resolution measurements, while the ADS1286UCG4 supports much higher sample rates at lower resolution.

Can the ADS1231IDR and ADS1286UCG4 be used interchangeably in an existing design?

No. Because they differ in resolution architecture (24-bit delta-sigma vs 12-bit SAR), package (8-pin SOIC vs 10-pin VSSOP), interface protocol, input configuration, and integration level (integrated PGA and excitation vs none), they cannot be used interchangeably without a complete redesign of the analog front end, PCB layout, and firmware.