ADS8555SPMR
Texas Instruments
- Lifecycle
- Active
- Stock
- 2733 Stückzahl
- Package
- LQFP-64
- Series
- Datenerfassung mit Analog to Digital Converters (ADC)
Dieser detaillierte Vergleich von ADS8555SPMR und ADS8555SPM bietet wertvolle Einblicke in deren Spezifikationen und Hauptmerkmale. Wir gehen ausführlich auf wichtige Faktoren ein, darunter RoHS-Konformität, REACH-Status, Serie, Montageart, Gehäusetyp und weitere relevante Eigenschaften. Die übersichtliche Darstellung der Unterschiede vereinfacht die Komponentenauswahl und erleichtert Ihnen die Wahl der optimalen Lösung für Ihre Anwendung.
Replacement verdict
The ADS8555SPMR and ADS8555SPM are functionally equivalent six-channel simultaneous-sampling SAR ADCs sharing identical core specifications, differing only in reel versus tray packaging. The ADS8555SPMR is a valid functional replacement for the ADS8555SPM, with the same electrical performance and footprint compatibility.
Texas Instruments
Texas Instruments
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADS8555SPMR | ADS8555SPM | Why it matters |
|---|---|---|---|
| Package / Case | LQFP-64 (10x10 mm) | LQFP-64 (10x10 mm) | The package footprint and pinout determine whether the part can be dropped onto an existing PCB without layout changes. |
| Packaging / Ordering Format | Tape & Reel (R suffix) | Tray / Tube (no R suffix) | The reel vs. tray distinction affects assembly line handling and is the primary difference between these two orderable part numbers. |
| Resolution | 16 bits | 16 bits | Resolution defines the smallest measurable signal step and must match for functional equivalence. |
| Number of ADC Channels | 6 (simultaneous sampling) | 6 (simultaneous sampling) | Channel count and simultaneous sampling capability determine suitability for multi-phase or multi-axis measurement systems. |
| Sampling Rate | 630 kSPS | 630 kSPS | Maximum throughput must meet the signal bandwidth requirements of the application. |
| Supply Voltage | 5 V analog, 2.7–5.5 V digital | 5 V analog, 2.7–5.5 V digital | Supply rails must be compatible with the existing power architecture for direct substitution. |
| Interface | Parallel / Serial (SPI-compatible) | Parallel / Serial (SPI-compatible) | The digital interface must match the host controller to avoid firmware or hardware redesign. |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C | The temperature range must cover the target environment for reliable operation. |
| Input Type | Bipolar, pseudo-differential | Bipolar, pseudo-differential | Input configuration determines signal conditioning requirements and measurement accuracy. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADS8555SPMR | ADS8555SPM |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC,Texas Instruments |
| Part Status | Active | Active |
| Number of Bits | 16 | 16 |
| Sampling Rate(Per Second) | 630k | 630k |
| Number of Inputs | 6 | 6 |
| Input Type | Single Ended | Single Ended |
| Data Interface | SPI, Parallel | SPI, Parallel |
| Configuration | S/H-ADC | S/H-ADC |
| Ratio - S / H: ADC | 1:1 | 1:1 |
| Number of A/D Converters | 1 | 1 |
| Architecture | SAR | SAR |
| Reference Type | External, Internal | External, Internal |
| Voltage - Supply, Analog | 5V | 5V |
| Voltage - Supply, Digital | 2.7V ~ 3.6V, 5V | 2.7V ~ 3.6V, 5V |
| Features | Simultaneous Sampling | Simultaneous Sampling |
| Operating Temperature | -40°C ~ 125°C | -40°C ~ 125°C |
Both devices are the same ADS8555 six-channel, 16-bit, simultaneous-sampling SAR ADC from Texas Instruments. The difference is the ordering suffix: the ADS8555SPM is supplied in tube/rail packaging, while the ADS8555SPMR is the tape-and-reel variant (R suffix). The electrical specifications, die, and LQFP-64 package are identical.
Yes. Both orderable part numbers share the same datasheet, silicon revision, and functional block diagram. They differ only in shipping media (tape-and-reel vs tube), so AC/DC performance, pinout, and register behavior are the same.
Both parts are offered in a 64-pin LQFP (PM package) with a 10 mm × 10 mm body and 0.5 mm lead pitch, as specified in the Texas Instruments ADS8555 datasheet.
Yes, from an electrical and footprint standpoint, since both are the same die in the same 64-pin LQFP package. The only practical consideration is the assembly process: tape-and-reel (R) suits automated pick-and-place lines, while tube (non-R) suits low-volume or manual handling.
Per the TI datasheet, both are 16-bit, 6-channel simultaneous-sampling SAR ADCs with up to 630 kSPS per channel, a ±10 V or ±5 V input range option, an integrated reference, and a parallel or serial interface. They operate from a 5 V analog supply with a 3.3 V or 5 V digital supply.
Both are intended for multi-axis motor control, power quality monitoring, protective relays, and industrial data acquisition where simultaneous sampling of multiple channels is required, as described in the TI product documentation.
Both are moisture-sensitive LQFP devices and should be handled per the moisture sensitivity level (MSL) stated on the TI package label and datasheet. Tape-and-reel (R) parts are typically supplied in reels for automated assembly, while tube parts require the same ESD and MSL precautions.