AMC1301DWVR
Texas Instruments
- Lifecycle
- Active
- Stock
- 6629 Stückzahl
- Series
- Linear-Verstärker.Instrumentation, OP-Verstärker, Pufferverstärker
Dieser detaillierte Vergleich von AMC1301DWVR und AMC1305M25DWR bietet wertvolle Einblicke in deren Spezifikationen und Hauptmerkmale. Wir gehen ausführlich auf wichtige Faktoren ein, darunter RoHS-Konformität, REACH-Status, Serie, Montageart, Gehäusetyp und weitere relevante Eigenschaften. Die übersichtliche Darstellung der Unterschiede vereinfacht die Komponentenauswahl und erleichtert Ihnen die Wahl der optimalen Lösung für Ihre Anwendung.
Replacement verdict
The AMC1305M25DWR and AMC1301DWVR are both isolated delta-sigma modulator amplifiers from Texas Instruments sharing a 16-pin SOIC-wide package and a nominal 5 V supply, but they differ in input structure, isolation rating, and output interface. The AMC1305M25DWR is a single-channel modulator with a ±250 mV differential input and CMOS output, while the AMC1301DWVR is a single-channel isolated amplifier with a ±250 mV input and differential analog output. Designers should validate the output interface, isolation working voltage, and clocking requirements before substituting one for the other in a given signal chain.
Texas Instruments
Texas Instruments
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | AMC1305M25DWR | AMC1301DWVR | Why it matters |
|---|---|---|---|
| Input Type | Current shunt (isolated delta-sigma modulator) | Voltage (isolated amplifier) | Determines whether the device measures current via a shunt or amplifies a voltage signal; these are fundamentally different signal-chain functions and are not directly substitutable. |
| Output Format | 1-bit digital bitstream (delta-sigma) | Analog differential voltage | A digital bitstream requires a digital filter/decoder on the controller side, while an analog output feeds an ADC; the downstream interface architecture differs completely. |
| Isolation Rating | 5000 V RMS (reinforced) | 3000 V RMS (basic) | Higher isolation rating allows use in higher-voltage or reinforced-insulation applications; substituting a lower-rated part may violate safety requirements. |
| Input Voltage Range | ±250 mV (shunt input) | ±250 mV (with ±320 mV linear range) | Both target small shunt signals, but the usable linear input window and overload behavior differ, affecting measurement accuracy and fault tolerance. |
| Supply Voltage | 3.3 V (high side) / 3.3 V or 5 V (low side) | 5 V (high side) / 3.3 V or 5 V (low side) | High-side supply requirements differ, so the isolated power supply design must match the chosen device. |
| Gain | Fixed (modulator, no analog gain stage) | Fixed gain of 8 | The analog amplifier provides a defined gain of 8, whereas the modulator encodes the signal digitally; scaling and signal conditioning differ. |
| Bandwidth | Up to ~20 MHz clock, signal bandwidth set by digital filter | ~100 kHz (typical) | The modulator supports much higher effective bandwidth when paired with a fast digital filter, while the amplifier bandwidth is fixed, affecting control-loop speed. |
| Package | SOIC-16 (wide body) | SOIC-8 (wide body) | Different pin count and footprint prevent drop-in board replacement without layout changes. |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +105 °C | The wider temperature range of the modulator suits harsher environments; the amplifier has a lower upper limit, affecting thermal margin. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | AMC1301DWVR | AMC1305M25DWR |
|---|---|---|
| Part Status | Active | Active |
| Amplifier Type | Isolation | - |
| Number of Circuits | 1 | - |
| Gain Bandwidth Product | 1 MHz | - |
| Current - Input Bias | 60 µA | - |
| Voltage - Input Offset | 50 µV | - |
| Supply Current | 5.9mA | - |
| Current - Output / Channel | 13 mA | - |
| Voltage - Supply Span(Min) | 3 V | - |
| Voltage - Supply Span(Max) | 5.5 V | - |
| Operating Temperature | -40°C ~ 125°C | -40°C ~ 125°C |
| Mounting Type | Surface Mount | Surface Mount |
| Type | - | Isolated Module |
| Number of Channels | - | 1 |
| Resolution(Bits) | - | 16 b |
| Sampling Rate(Per Second) | - | 78k |
| Data Interface | - | CMOS, Serial |
| Voltage Supply Source | - | Analog and Digital |
| Voltage - Supply | - | 3V ~ 5.5V |
The AMC1305M25DWR is a reinforced isolated delta-sigma modulator with a ±250 mV input range and a 20 MHz clock, designed for shunt-based current sensing with a bit-stream output. The AMC1301DWVR is a precision isolated amplifier with a ±250 mV input range and a fixed gain of 8.2, providing a differential analog output. The modulator outputs a 1-bit data stream, while the amplifier outputs an analog voltage, so they serve different signal-chain architectures.
No. Both devices are offered in a 16-pin SOIC (DW) package, but their pin functions differ: the AMC1305M25DWR provides a clock input and a single-bit modulator data output, whereas the AMC1301DWVR provides a differential analog output with fixed gain. The pinouts are not interchangeable, and PCB layouts must be designed for the specific device.
Both devices are reinforced isolated components rated for 5 kV RMS isolation per UL 1577 and provide a working voltage of 1.5 kV peak per VDE V 0884-10 (VDE 0884-10). They are intended for galvanically isolated current and voltage sensing in high-voltage systems.
Both devices are specified for a linear input range of ±250 mV, making them suitable for shunt-resistor-based current sensing where the shunt voltage is small. The AMC1305M25DWR digitizes this input with a delta-sigma modulator, while the AMC1301DWVR amplifies it with a fixed gain of 8.2 to produce a differential analog output.
The AMC1305M25DWR is the appropriate choice when the system includes a digital filter (such as an FPGA or a sigma-delta modulator filter) because it outputs a 1-bit delta-sigma bit stream at a 20 MHz clock rate. The AMC1301DWVR outputs an analog signal and would require an external ADC, so it is better suited to designs that already have an analog-to-digital conversion stage.
Both devices use a 5 V analog supply on the high-voltage side and a 3.3 V or 5 V supply on the low-voltage side, depending on the specific variant and configuration. Designers should confirm the exact supply rails and decoupling requirements from the respective datasheets, as the low-side supply options and output interface differ between the modulator and the amplifier.
No. The AMC1305M25DWR produces a digital bit-stream output requiring a digital filter, while the AMC1301DWVR produces an analog output requiring an ADC. Because the output interfaces, pin functions, and signal-chain requirements differ, a direct replacement is not possible without redesigning the receiving circuitry and PCB layout.