ADM489ARZ
Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 3659 Stückzahl
- Package
- SOIC-14
- Series
- Interface-Treiber, Empfänger, Transceiver
Dieser detaillierte Vergleich von ADM489ARZ und ADM4852AR bietet wertvolle Einblicke in deren Spezifikationen und Hauptmerkmale. Wir gehen ausführlich auf wichtige Faktoren ein, darunter RoHS-Konformität, REACH-Status, Serie, Montageart, Gehäusetyp und weitere relevante Eigenschaften. Die übersichtliche Darstellung der Unterschiede vereinfacht die Komponentenauswahl und erleichtert Ihnen die Wahl der optimalen Lösung für Ihre Anwendung.
Replacement verdict
The ADM489ARZ and ADM4852AR are both half-duplex RS-485/RS-422 transceivers in an 8-lead SOIC package with a 5 V supply and similar data rates, making the ADM4852AR a viable functional replacement candidate for the ADM489ARZ in many designs. However, the ADM489ARZ integrates a proprietary RS-485 driver with a wider common-mode range and full fail-safe receiver behavior, while the ADM4852AR offers a standard pinout with a lower unit-load receiver input and different ESD and fail-safe characteristics. Designers should validate receiver fail-safe behavior, common-mode performance, and ESD robustness against the specific bus environment before substituting.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM489ARZ | ADM4852AR | Why it matters |
|---|---|---|---|
| Data Rate | 250 kbps | 2.5 Mbps | Maximum signaling speed; the ADM4852AR supports roughly 10x higher throughput, so it can serve faster buses while the ADM489ARZ is limited to lower-speed networks. |
| Duplex Mode | Full duplex | Half duplex | Full duplex allows simultaneous transmit and receive (four-wire bus), while half duplex shares one pair; this fundamentally changes wiring and whether the parts are drop-in substitutes. |
| Number of Drivers / Receivers | 1 driver / 1 receiver | 1 driver / 1 receiver | Transceiver channel count determines bus topology compatibility; both are single-channel, so this aspect is equivalent. |
| Supply Voltage | 5 V | 5 V | Operating supply rail must match the system power domain; both run from a single 5 V supply, so power design is compatible. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Industrial temperature range affects suitability for harsh environments; identical ranges mean equal environmental robustness. |
| Mounting / Package | Surface mount, 14-lead SOIC | Surface mount, 8-lead SOIC | Package footprint and pin count must match the PCB layout; the different SOIC sizes mean they are not footprint-compatible without a board redesign. |
| Receiver Input Impedance (Unit Loads) | 1 unit load (standard RS-485) | 1 unit load (standard RS-485) | Unit-load rating determines how many nodes can share a bus; both being 1 unit load allows up to 32 standard nodes. |
| Fail-Safe Receiver | Yes (open-circuit fail-safe) | Yes (open-circuit fail-safe) | Fail-safe biasing guarantees a defined logic state when the bus is idle or disconnected, preventing spurious data; both provide this feature. |
| ESD Protection (Bus Pins) | ±15 kV (HBM, bus pins) | ±15 kV (HBM, bus pins) | Bus-pin ESD robustness affects field reliability in exposed cabling; equal ratings mean comparable protection levels. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM489ARZ | ADM4852AR |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC |
| Part Status | Active | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS422, RS485 | RS422, RS485 |
| Number of Drivers/Receivers | 1/1 | 1/1 |
| Voltage - Supply | 4.5V ~ 5.5V | 4.75V ~ 5.25V |
| Mounting Type | Surface Mount | Surface Mount |
| Duplex | Full | - |
| Receiver Hysteresis | 70 mV | - |
| Data Rate | 250kbps | - |
| Operating Temperature | -40°C ~ 85°C | - |
The ADM489ARZ is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver specified for data rates up to 250 kbps, while the ADM4852AR is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 2.5 Mbps. The ADM489ARZ provides separate driver and receiver enable pins for full-duplex operation, whereas the ADM4852AR uses a single direction-control pin for half-duplex operation.
No. The ADM489ARZ is supplied in a 14-lead SOIC package with separate driver and receiver enable pins and dedicated full-duplex A/B and Y/Z bus pins, while the ADM4852AR is supplied in an 8-lead SOIC package with a single DE/RE direction pin and half-duplex A/B bus pins. The pin counts and pin functions differ, so they are not drop-in replacements.
No, not without design changes. The ADM489ARZ supports full-duplex communication with independent driver and receiver enables, while the ADM4852AR supports half-duplex communication with a single direction-control pin. Bus wiring, PCB footprint, and firmware control logic must be revalidated before substituting one for the other.
The ADM489ARZ is specified for data rates up to 250 kbps. The ADM4852AR is specified for data rates up to 2.5 Mbps. The higher rate of the ADM4852AR makes it suitable for faster half-duplex buses, while the ADM489ARZ targets lower-speed full-duplex applications.
Yes. Both the ADM489ARZ and the ADM4852AR are specified for operation from a single 5 V ±5% supply, consistent with the standard RS-485/RS-422 supply rail.
Both devices feature RS-485/RS-422-compliant differential receiver inputs with a common-mode range of -7 V to +12 V and a receiver input sensitivity of ±200 mV, allowing detection of differential signals as low as 200 mV over the specified common-mode range.
The ADM489ARZ is offered in a 14-lead SOIC package (the "RZ" suffix denotes RoHS-compliant SOIC). The ADM4852AR is offered in an 8-lead SOIC package (the "AR" suffix denotes SOIC). Package selection should be based on the required duplex mode and pin count.
The ADM489ARZ should be selected for full-duplex RS-485/RS-422 buses because it provides independent driver and receiver enable control and separate transmit and receive bus pairs. The ADM4852AR is a half-duplex device and is not suitable for full-duplex bus topologies without external multiplexing.