ADS7843E/2K5 vs ADS7842EB

Dieser detaillierte Vergleich von ADS7843E/2K5 und ADS7842EB bietet wertvolle Einblicke in deren Spezifikationen und Hauptmerkmale. Wir gehen ausführlich auf wichtige Faktoren ein, darunter RoHS-Konformität, REACH-Status, Serie, Montageart, Gehäusetyp und weitere relevante Eigenschaften. Die übersichtliche Darstellung der Unterschiede vereinfacht die Komponentenauswahl und erleichtert Ihnen die Wahl der optimalen Lösung für Ihre Anwendung.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Not a drop-in replacement

The ADS7843E/2K5 and ADS7842EB are not drop-in replacements for one another. The ADS7843E/2K5 is a 4-wire resistive touch screen controller with an SPI-compatible serial interface, while the ADS7842EB is a 4-channel 12-bit parallel-output successive-approximation ADC. Their differing interface architecture, channel configuration, package footprint, and control signaling make direct substitution impractical without a full board and firmware redesign.

Different output interface Different channel configuration Different package footprint Different control signaling

Parts at a glance

Part A

ADS7843E/2K5

Texas Instruments

Lifecycle
Active
Stock
2859 Stückzahl
Package
SSOP-16
Series
Datenerfassung mit Touchscreen Controllern
Part B

ADS7842EB

Burr Brown

Lifecycle
Active
Stock
8281 Stückzahl
Package
SSOP-28
Series
Datenerfassung mit Analog to Digital Converters (ADC)

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADS7843E/2K5 ADS7842EB Why it matters
Resolution 12 bit 12 bit Both are 12-bit devices, so conversion resolution is equivalent for touch or signal digitization accuracy.
Number of Input Channels 4 (single-ended/differential touch channels) 4 (single-ended) Channel configuration affects whether the part can directly support 4-wire resistive touchscreen X/Y measurement versus general analog input multiplexing.
Interface Type SPI (serial) Parallel The digital interface must match the host microcontroller or processor bus; SPI versus parallel is a major functional substitutability constraint.
Supply Voltage 2.7 V to 5.25 V 5 V (single supply) Operating supply range determines compatibility with the system power rail and logic levels.
Package SSOP-16 SSOP-28 Package footprint and pin count must match the PCB layout for a drop-in replacement.
Primary Application 4-wire resistive touchscreen controller General-purpose 4-channel ADC The intended function differs; one integrates touchscreen control logic while the other is a general ADC, affecting direct substitutability.
Pin Count 16 28 Different pin counts mean the devices are not pin-compatible and cannot be interchanged on the same footprint.
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C Equivalent temperature ratings mean both suit the same industrial temperature environments.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADS7843E/2K5 ADS7842EB
Supplier - Rochester Electronics, LLC
Part Status Active Active
Number of Bits - 12
Sampling Rate(Per Second) - 200k
Number of Inputs - 4
Input Type - Single Ended
Data Interface - Parallel
Configuration - MUX-S/H-ADC
Ratio - S / H: ADC - 1:1
Number of A/D Converters - 1
Architecture - SAR
Reference Type - External
Voltage - Supply, Analog - 2.7V ~ 3.6V, 5V
Voltage - Supply, Digital - 2.7V ~ 3.6V, 5V
Features - Selectable Address
Operating Temperature -40°C ~ 85°C -40°C ~ 85°C
Touchscreen 4 Wire Resistive -
Resolution(Bits) 12 b -
Interface Serial -
Voltage Reference External -
Voltage - Supply 2.7V ~ 5V -
Supply Current 2.5 µA -
Mounting Type Surface Mount -

Frequently asked questions

Are the ADS7843E/2K5 and ADS7842EB functionally interchangeable?

No. The ADS7843E/2K5 is a 4-wire resistive touch screen controller with a 12-bit SAR ADC and an SPI-compatible serial interface, while the ADS7842EB is a 4-channel, 12-bit parallel-output sampling ADC. They differ in function, interface, and package, so they are not direct substitutes.

What is the resolution and architecture of each device?

Both devices use a 12-bit successive-approximation register (SAR) ADC architecture. The ADS7843E/2K5 provides 12-bit resolution for touch screen coordinate measurement, and the ADS7842EB provides 12-bit resolution across four analog input channels.

How do the digital interfaces of the ADS7843E/2K5 and ADS7842EB differ?

The ADS7843E/2K5 uses an SPI-compatible 3-wire serial interface for communication with a host controller. The ADS7842EB provides a parallel digital output interface, requiring multiple data lines plus control signals, which affects host pin count and PCB routing.

What are the package differences between the ADS7843E/2K5 and ADS7842EB?

The ADS7843E/2K5 is supplied in a TSSOP package, while the ADS7842EB is supplied in an SSOP package. The different package types and pinouts mean the two devices are not footprint-compatible and cannot be dropped into the same PCB land pattern.

What are the typical supply voltage requirements for these devices?

The ADS7843E/2K5 operates from a single supply in the 2.7 V to 5 V range, supporting both 3 V and 5 V systems. The ADS7842EB operates from a single 5 V supply. Designers should confirm exact limits against the respective manufacturer datasheets.

What are the primary application differences between the ADS7843E/2K5 and ADS7842EB?

The ADS7843E/2K5 is intended for 4-wire resistive touch screen digitizer applications, handling pen position and pressure measurement. The ADS7842EB is a general-purpose 4-channel data acquisition ADC suited to multi-channel signal sampling rather than touch screen control.

Can the ADS7842EB be used as a touch screen controller replacement for the ADS7843E/2K5?

No. The ADS7842EB lacks the touch screen drive and switching circuitry and the serial interface of the ADS7843E/2K5, so it cannot directly perform 4-wire resistive touch screen control. Any substitution would require substantial redesign and external circuitry.